您的当前位置：首页 8800D

8800D

来源：华佗小知识

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

Rosemount 8800D Series Vortex Flowmeter

HART® AND FOUNDATION™ FIELDBUS PROTOCOLS

•Available with optional MultiVariable output and temperature compensated mass flow for saturated steam.

•Available in wafer, flanged, dual, reducer and high pressure designs.

•Only manufacturer of Reducer™ Vortex which extends the measurable flow range, reduces installation costs, and minimizes project risk.•All-welded, non-clog design eliminates ports and gaskets.

•Patented Adaptive Digital Signal Processing (ADSP) provides vibration immunity.•Unique isolated sensor design allows

replacement without breaking the process seal.

•Simplified troubleshooting through device diagnostics.

Contents

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pageFlow-6Product Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pageFlow-22Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pageFlow-29Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pageFlow-44

www.rosemount.com

Product Data Sheet

Rosemount 8800D

•

00813-0100-4004, Rev FA

Catalog 2008 - 2009

THE ROSEMOUNT 8800D DELIVERS RELIABILITY

Rosemount Reliability -The 8800D Vortex eliminates impulse lines, ports, and gaskets to improve reliability.

Non-clog Design - Unique gasket-free

construction which has no ports that can clog.Vibration Immunity - Mass Balancing of the sensor system, and Patented Adaptive Digital Signal Processing (ADSP) provide Vibration immunity.

Replaceable Sensor - The sensor is isolated from the process and can be replaced without breaking the process seals. All line sizes use the same sensor design allowing a single spare to serve every meter.

Simplified Troubleshooting - Device

Diagnostics enable field verification of Meter Electronics and Sensor with no process shutdown.

••

•

THE ROSEMOUNT 8800D OFFERING

•

The 8800D is available in wafer style meter bodies for 1/2 through 8 in. line sizes, and

ASME B16.5 (ANSI), DIN, or JIS flanged style meter bodies for 1/2 through 12 in. line sizes. Alignment rings, provided with each

wafer-style flowmeter, ensure that the meter body is properly centered with the adjacent piping.

Both wafer and flanged style meter bodies are available in 316L stainless steel and nickel alloy materials of construction.

Available up to ANSI class 1500 for 1 through 8 in. (25 mm through 200 mm) and ANSI class 900 for 1/2 in. (15 mm) through 8 in. (200 mm).Available with FOUNDATION fieldbus functionality which includes Device Diagnostics and PlantWeb Alerts.

•

Flow-2

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

THE ROSEMOUNT 8800DR REDUCER™ VORTEX EXTENDS THE MEASURABLE

FLOW RANGE AT A REDUCED COST

•

Rosemount Reliability - Designed with same electronics, sensor, and meter body as the 8800D.

Reduced Cost - Eliminates field assembly and welding of separate reducers and piping reducing installed cost by as much as 50%.Extended Measurable Flow - Low-end flow range is doubled with the Rosemount 8800DR Reducer Vortex.

Reduced Project Risk - Reducer Vortex and the Standard Vortex have the same

face-to-face dimension. As a result either meter can be used without affecting pipe layout.

Available as flanged meter for 1 through 12 in. stainless steel and nickel alloy materials of construction.

Available with FOUNDATION fieldbus functionality.

•

THE DUAL-SENSOR VORTEX FLOWMETER

•

Safety Integrated Systems (SIS) - Ideal solution where redundant flow signals are required.

Rosemount Reliability - Designed with same electronics, sensor, and meter body as the 8800D.

Redundant Flow Measurement - Dual Vortex meter is constructed of two complete vortex meters: sensor, electronics, and shedder bar(1). The meters are welded together and flow calibrated to provide an accurate single flowmeter with two independent flow measurements.

Available as flanged meter for 1/2 through 12 in. stainless steel and nickel alloy materials of construction.

•

(1)

All 10 in (250 mm) and 12 in (300 mm) dual style vortex meters have a single shedder bar. 6 in (150 mm) and 8 in (200 mm) dual style vortex meters with 900# or 1500# flange ratings have a single shedder bar.

Flow-3

Product Data Sheet

Rosemount 8800D

00813-0100-4004, Rev FA

Catalog 2008 - 2009

8800D MULTIVARIABLE VORTEX REDUCES INSTALLATION COSTS, SIMPLIFIES

INSTALLATION, AND IMPROVES PERFORMANCE IN SATURATED STEAM

•

MultiVariable Vortex Design

Incorporates temperature sensor into the vortex meter using the shedder bar as a thermowell, which keeps the vortex and

temperature sensor isolated from process for easy verification and replacement.

Temperature Compensated Capability for Saturated Steam

Calculates density from measured process temperature and uses the calculated density to provide a temperature compensated mass flow.

Increased performance in Saturated Steam

Performance in saturated steam is improved due to the fact that the electronics will be compensating for changes in the process temperature.

Reduces Installed Costs

MultiVariable Vortex eliminates the need for an external thermowell and temperature sensor.

Output Options

Can map independent variables to analog output, pulse output, or HART burst variables.Available with Flow Computer for additional functionality

Integrate the MultiVariable Vortex with a pressure transmitter for full pressure and temperature compensation of superheated steam and various gases.

Remote Mount Electronics

Also available with remote mounted electronics up to 75 ft. (23 m)

•

When you integrate the MultiVariable Vortex with a Rosemount Flow Computer, you get:•••••

Remote CommunicationsHeat CalculationsRemote TotalizationPeak Demand CalculationDatalogging Capabilities

Please see Product Data Sheet 00813-0100-4005 for more information on the Rosemount Flow Computer.

Flow-4

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

ROSEMOUNT 8800D VORTEX FLOWMETER WITH FOUNDATION FIELDBUS

The software for the 8800D Flowmeter with

FOUNDATION fieldbus permits remote testing and configuration using any FOUNDATION

fieldbus-compliant host, such as the DeltaV system from Emerson Process Management.

Transducer Block

The transducer block calculates flow from sensor frequency. The calculation includes information about damping, shedding frequency, K-factor, service type, pipe ID, and diagnostics.

Resource Block

The resource block contains physical transmitter information, including available memory,

manufacturer identification, device type, software tag, and unique identification.

Backup Link Active Scheduler (LAS)

The transmitter is classified as a device link master. A device link master can function as a Link Active Scheduler (LAS) if the current link master device fails or is removed from the segment.

The host or other configuration tool is used to

download the schedule for the application to the link master device. In the absence of a primary link

master, the transmitter will claim the LAS and provide permanent control for the H1 segment.

Diagnostics

The transmitter automatically performs continuous self-diagnostics. The user can perform on-line testing of the transmitter digital signal. Advanced simulation diagnostics are available. This enables remote verification of the electronics via a flow signal generator built into the electronics. The sensor

strength value can be used to view the process flow signal and provide information regarding filter settings.

Rosemount 8800D

FOUNDATION Fieldbus Function Blocks

Analog Input

The AI function block processes the measurement and makes it available to other function blocks. The AI function block also allows filtering, alarming, and engineering unit changes.

The 8800D Flowmeter with FOUNDATION fieldbus comes standard with two AI function blocks (1 block for flow and 1 block for signal strength).Proportional/Integral/Derivative

The optional PID function block provides a

sophisticated implementation of the universal PID algorithm. The PID function block features input for feed forward control, alarms on the process variable, and control deviation. The PID type (series or Instrument Society of America [ISA]) is user-selectable on the derivative filter.

Integrator

The standard integrator block is available for totalization of flow.

Setup

Basic setup requires connecting the transmitter to a fieldbus network or 375 Handheld Communicator. The FOUNDATION fieldbus- compliant host will automatically establish communication with the device.

The Rosemount 8800D Flowmeter can be easily configured using the DeltaV system.

User-configurable parameters include: tag, scaling and units, service type, damping, process density, pipe inside diameter (ID)(1), and process temperature(1).

Tagging information can be entered into the transmitter to allow identification and a physical description. 32-character tags are provided for identification of the transmitter and each function block.

(1)

Process temperature and pipe ID have known effects on the K-factor. The 8800D software automatically

accounts for these effects by compensating the K-factor.

Flow-5

Product Data Sheet

Rosemount 8800D

Specifications

00813-0100-4004, Rev FA

Catalog 2008 - 2009

The following specifications are for the Rosemount 8800D, Rosemount 8800DR, and Rosemount 8800DD, except where noted.

FUNCTIONAL SPECIFICATIONS

Service

Liquid, gas, and steam applications. Fluids must be homogeneous and single-phase.Line Sizes

Wafer1

/2, 1, 11/2, 2, 3, 4, 6, and 8 inches

(DN 15, 25, 40, 50, 80, 100, 150, and 200)Flanged and Dual-Sensor Style1

/2, 1, 11/2, 2, 3, 4, 6, 8, 10, and 12 inches

(DN 15, 25, 40, 50, 80, 100, 150, 200, 250, and 300)

Reducer

1, 11/2, 2, 3, 4, 6, 8, 10, and 12 inches

(DN 25, 40, 50, 80, 100, 150, 200, 250, and 300)Pipe Schedules

Process piping Schedules 10, 40, 80, and 160.NOTE

The appropriate bore diameter of the process piping must be entered using the HART Communicator or AMS. Meters will be shipped from the factory at the Schedule 40 default value unless otherwise specified.

Measurable Flow Rates

Capable of processing signals from flow applications which meet the sizing requirements below. To determine the appropriate flowmeter size for an application, process conditions must be within the Reynolds number and velocity limitations for the desired line size provided in Table1, Table2, Table3, and Table4.

Flow-6

NOTE

Consult your local sales representative to obtain a computer sizing program that describes in greater detail how to specify the correct flowmeter size for anapplication.

The Reynolds number equation shown below combines the effects of density (␳), viscosity (␮velocity (V).

cp), pipe inside diameter (D), and flow RD=VD--µ-------ρ--cp

TABLE 1. Minimum Measurable Meter Reynolds Numbers

1/2 through 4/15 through 10010000 minimum6 through 12/150 through 300

20000 minimum

TABLE 2. Minimum Measurable Meter Velocities(1)(Use the larger of the two values)

Liquids(2)36/ρ or 0.754/ρ or 0.22

Gases36/ρ or 6.554/ρ or 2.033(1)Velocities are referenced to schedule 40 pipe.

(2)The minimum measurable velocity for the 10in. line size is 0.94 ft/s

(.29m/s) and 1.11 ft/s (.34m/s) for the 12in. line size.

TABLE 3. Maximum Measurable Meter Velocities(1)(Use the smaller of the two values)

Liquids90,000/ρ or 25134,000/ρ or 7.6Gases

(2)90,000/ρ or 250134,000/ρ or 76

33(1)Velocities are referenced to schedule 40 pipe.

(2)Accuracy limitations for gas and steam for Dual-style meters (1/2”

to 8”): max velocity of 100 ft/s (30.5 m/s).

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Process Temperature LimitsStandard

–40 to 450 °F (–40 to 232 °C)Extended

–330 to 800 °F (–200 to 427 °C)

MultiVariable (MTA option)–40 to 800 °F (–40 to 427 °C)

★ Use above 450 °F (232 °C) requires Extended SensorOutput Signals

4–20 mA Digital HART Signal Superimposed on 4–20 mA signal

Optional Scalable Pulse Output

0 to 10000 Hz; transistor switch closure with adjustable scaling via HART communications; capable of switching up to 30 V dc, 120 mA maximum

Digital Foundation fieldbus signal

Manchester-encoded digital signal that conforms to IEC 1158-2 and ISA 50.02. Analog Output Adjustment

Engineering units and lower and upper range values are user-selected. Output is automatically scaled to provide 4 mA at the selected lower range value, 20mA at the selected upper range value. No frequency input is required to adjust the range values.

Scalable Frequency Adjustment

The scalable pulse output can be set to a specific velocity, volume, or mass (i.e. 1 pulse = 1 lb). The scalable pulse output can also be scaled to a specific rate of volume, mass, or velocity (i.e. 100 Hz = 500 lb/hr).

Ambient Temperature Limits

Operating

–58 to 185 °F (–50 to 85 °C)

–4 to 185 °F (–20 to 85 °C) for flowmeters with local indicator

Storage

–58 to 250 °F (–50 to 121 °C)

–50 to 185 °F (–46 to 85 °C) for flowmeters with local indicator

Rosemount 8800D

Pressure Limits

Flange Style Meter

Rated for ASME B16.5 (ANSI) Class 150, 300, 600, 900, and 1500, DIN PN 10, 16, 25, 40, , 100, and 160, and JIS 10K, 20K, and 40KReducer Style Meter

Rated for ASME B16.5 (ANSI) Class 150, 300, 600, and 900, DIN PN 10, 16, 25, 40, , 100, and 160.

Dual Sensor Style Meter

Rated for ASME B16.5 (ANSI) Class 150, 300, 600, 900, and 1500, DIN PN 10, 16, 25, 40, , 100, and 160, and JIS 10K, 20K, and 40KWafer Style Meter

Rated for ASME B16.5 (ANSI) Class 150, 300, and 600, DIN PN 10, 16, 25, 40, , and 100, and JIS 10K, 20K, and 40K

Weld-End Style Meter

W1 Welds to Schedule 10 mating pipe

Max Working Pressure 720 psig (4.96 MPa-g)W4 Welds to Schedule 40 mating pipe

Max Working Pressure 1440 psig (9.93 MPa-g)W8 Welds to Schedule 80 mating pipe

Max Working Pressure 2160 psig (14.9 MPa-g)W9 Welds to Schedule 160 mating pipe Note: 1” (25 mm), and 1.5” (40 mm) weld to Schedule 80 mating pipe

Max Working Pressure 3600 psig (24.8 Mpa-g)Power Supply

HART Analog

External power supply required. Flowmeter

operates on 10.8 to 42 V dc terminal voltage (with 250-ohm minimum load required for HART communications, 16.8 V dc power supply is required)

Foundation fieldbus

External power supply required. Flowmeter

operates on 9 to 32 V dc, 17.8 mA nominal, 20.0 mA maximum. Power ConsumptionOne watt maximum

Flow-7

Rosemount 8800D

Load Limitations (HART Analog)

Maximum loop resistance is determined by the voltage level of the external power supply, as described by:

12501000)smhO(Operating dRegion

a500oL010.8

42Power Supply (Volts)

Rmax =41.7(VVps – 10.8)

ps =Power Supply Voltage (Volts)

Rmax =

Maximum Loop Resistance (Ohms)

NOTE

HART Communication requires a minimum loop resistance of 250 ohms.Optional LCD Indicator

The optional LCD indicator is capable of displaying:•Primary Variable•Velocity Flow•Volumetric Flow•Mass Flow•Percent of Range

•Analog Output (if applicable)

•Totalizer (Output Code “D” and “P” Only)•Shedding Frequency

•Pulse Output Frequency (if applicable)•Electronics Temperature (Output Code “D” and “P” Only)

•Process Temperature (MTA Option Only)•

Calculated Process Density (MTA Option Only)

If more than one item is selected, the display will scroll through all items selected.Enclosure Rating

FM Type 4X; CSA Type 4X; IP66

Flow-8

Product Data Sheet

00813-0100-4004, Rev FA

Catalog 2008 - 2009

Permanent Pressure Loss

The approximate permanent pressure loss (PPL) from the Rosemount 8800D flowmeter is calculated for each application in the Vortex sizing software available from your local Rosemount representative. The PPL is determined using the equation:

PPLA------×----ρ----f---×-----Q2

=D4

-------

where:

PPL =Permanent Pressure loss (psi or kPa)

Where:

␳f =Density at operating conditions (lb/ft33 or

kg/m)

Q =Actual volumetric flow rate (Gas = ft33/min or

m/hr; Liquid = gal/minorl/min)

D =Flowmeter bore diameter (in.ormm)

A =Constant depending on meter style, fluid type

and flow units. Determined per following table:

TABLE 4. Determining the PPL

8800DF/W3.4 ϫ 10-51.9 ϫ 10-30.4251188800DR3.91 ϫ 10-52.19 ϫ 10-30.41368800DD(1)6.12 ϫ 10-53.42 ϫ 10-30.765

212

(1)For all 10 and 12 in (250 and 300 mm) line sizes and 6 and 8 in

(150 and 200 mm) with 900# or 1500# Flanges, A for Rosemount 8800DD is the same as Rosemount 8800DF.

Minimum Back Pressure (Liquids)

Flow metering conditions that would allow cavitation, the release of vapor from a liquid, should be avoided. This flow condition can be avoided by remaining within the proper flow range of the meter and by following appropriate system design.

For some liquid applications, incorporation of a back pressure valve should be considered. To prevent cavitation, the minimum back pressure should be:P =2.9∗ΔP + 1.3∗pv or P = 2.9∗ΔP + pv + 0.5 psia

(3.45 kPa) (use the smaller of the two results)P =Line pressure five pipe diameters downstream

of the meter (psia or kPa abs)

ΔP =Pressure loss across the meter (psi or kPa)pv =Liquid vapor pressure at operating conditions

(psia or kPa abs)

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Failure Mode Alarm

HART Analog

If self-diagnostics detect a gross flowmeter failure, the analog signal will be driven to the values below:

Low3.75High

22.6NAMUR Low3.60NAMUR High

22.6

High or low alarm signal is user-selectable through the fail mode alarm jumper on the

electronics. NAMUR-compliant alarm limits are available through the C4 or CN Option. Alarm type is field configurable also.

Foundation fieldbus

The AI block allows the user to configure the alarm to HI-HI, HI, LO, or LO-LO with a variety of priority levels.

Saturation Output Values

When the operating flow is outside the range points, the analog output continues to track the operating flow until reaching the saturation value listed below; the output does not exceed the listed saturation value regardless of the operating flow. The

NAMUR-Compliant Saturation Values are available through the C4 or CN option. Saturation type is field configurable.

Low3.9High

20.8NAMUR Low3.8NAMUR High

20.5

Damping

Flow Damping adjustable between 0.2 and 255 seconds.

Process Temperature Damping adjustable between 4.0 and 32.0 seconds (MTA Option Only).Response Time

Three vortex shedding cycles or 300 ms, whichever is greater, maximum required to reach 63.2% of actual input with the minimum damping (0.2 seconds).

Rosemount 8800D

Turn-on Time

HART Analog

Less than four (4) seconds plus the response time to rated accuracy from power up (less than 7 seconds with the MTA Option).

Foundation fieldbus

Performance within specifications no greater than 10.0 seconds after power is applied.Transient Protection

The optional transient terminal block prevents

damage to the flowmeter from transients induced by lightning, welding, heavy electrical equipment, or switch gears. The transient protection electronics are located in the terminal block.

The transient terminal block meets the followingspecifications:

ASME B16.5 (ANSI)/IEEE C62.41 - 1980 (IEEE587) Categories A, B 3 kA crest (8 ϫ 20 μs)6 kV crest (1.2 ϫ 50 μs)

6 kV/0.5 kA (0.5 μs, 100 kHz, ring wave)Security Lockout

When the security lockout jumper is enabled, the electronics will not allow you to modify parameters that affect flowmeter output.

Output Testing

Current Source

Flowmeter may be commanded to set the current to a specified value between 4 and 20 mA.Frequency Source

Flowmeter may be commanded to set the frequency to a specified value between 0and10000Hz.Low Flow Cutoff

Adjustable over entire flow range. Below selected value, output is driven to 4 mA and zero pulse output frequency.Humidity Limits

Operates in 0–95% relative humidity under

noncondensing conditions (tested to IEC 60770, Section 6.2.11).

Flow-9

Rosemount 8800D

Overrange Capability

HART Analog

Analog signal output continues to 105 percent of span, then remains constant with increasing flow. The digital and pulse outputs will continue to indicate flow up to the upper sensor limit of the flowmeter and a maximum pulse output frequency of 10400 Hz.

Foundation fieldbus

For liquid service type, the transducer block digital output will continue to a nominal value of 25 ft/s. After that, the status associated with the

transducer block output will go to UNCERTAIN. Above a nominal value of 30 ft/s, the status will go to BAD.

For gas/steam service, the transducer block digital output will continue to a nominal value of 220 ft/s for 0.5 and 1.0 in. line sizes and a nominal value of 250 ft/s for 1.5–12 in. line sizes. After that, the status associated with the transducer block output will go to UNCERTAIN. Above a nominal value of 300 ft/s for all line sizes, the status will go to BAD.Flow Calibration

Meter bodies are flow-calibrated and assigned a unique calibration factor (K-factor) at the factory. The calibration factor is entered into the electronics, enabling interchangeability of electronics and/or sensors without calculations or compromise in accuracy of the calibrated meter body.Status (FOUNDATION fieldbus only)

If self-diagnostics detect a transmitter failure, the status of the measurement will inform the control system. Status may also set the PID output to a safe value.

Schedule Entries (FOUNDATION fieldbus only)Six (6)

Links (FOUNDATION fieldbus only)Twelve (12)

Flow-10

Product Data Sheet

00813-0100-4004, Rev FA

Catalog 2008 - 2009

Virtual Communications Relationships (VCRs) (FOUNDATION fieldbus only)Two (2) predefined (F6, F7)

Four (4) configured (see Table 5)

TABLE 5. Block Information.

Resource (RB)300—Transducer (TB)400—Analog Input (AI)1,00020Proportional/

10,00030Integral/Derivative (PID)

Integrator (INT)

12,000

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

TABLE 6. Typical pipe velocity ranges for 8800D and 8800DR(1)

0.5/ 151/ 251.5/ 402/ 503/ 804/ 1006/ 1508/ 20010/ 25012/ 300

8800DF0058800DF0108800DR0108800DF0158800DR0158800DF0208800DR0208800DF0308800DR0308800DF0408800DR0408800DF0608800DR0608800DF0808800DR0808800DF1008800DR1008800DF1208800DR120

0.70 to 25.00.70 to 25.00.25 to 8.80.70 to 25.00.30 to 10.60.70 to 25.00.42 to 15.20.70 to 25.00.32 to 11.30.70 to 25.00.41 to 14.50.70 to 25.00.31 to 11.00.70 to 25.00.40 to 14.40.90 to 25.00.44 to 15.91.10 to 25.00.63 to 17.6

0.21 to 7.60.21 to 7.60.08 to 2.70.21 to 7.60.09 to 3.20.21 to 7.60.13 to 4.60.21 to 7.60.10 to 3.50.21 to 7.60.12 to 4.40.21 to 7.60.09 to 3.40.21 to 7.60.12 to 4.40.27 to 7.60.13 to 4.80.34 to 7.60.19 to 5.4

6.50 to 250.06.50 to 250.02.29 to 87.96.50 to 250.02.76 to 106.16.50 to 250.03.94 to 151.76.50 to 250.02.95 to 113.56.50 to 250.03.77 to 145.26.50 to 250.02.86 to 110.26.50 to 250.03.75 to 144.46.50 to 250.04.12 to 158.66.50 to 250.04.58 to 176.1

1.98 to 76.21.98 to 76.20.70 to 26.81.98 to 76.20.84 to 32.31.98 to 76.21.20 to 46.21.98 to 76.20.90 to 34.61.98 to 76.21.15 to 44.31.98 to 76.20.87 to 33.61.98 to 76.21.14 to 44.01.98 to 76.21.26 to 48.31.98 to 76.21.40 to 53.7

(1)Table6 is a reference of pipe velocities that can be measured for the standard Rosemount 8800D and the reducer Rosemount 8800DR Vortex Meters. It

does not consider density limitations, as described in tables 2 and 3. Velocities are referenced in schedule 40 pipe.(2)Velocity range of the Rosemount 8800DW is the same as Rosemount 8800DF.

TABLE 7. Water Flow Rate Limits for the Rosemount 8800D and 8800DR(1)

0.5/ 151/ 251.5/ 402/ 503/ 804/ 1006/ 1508/ 20010/ 25012/ 300

8800DF0058800DF0108800DR0108800DF0158800DR0158800DF0208800DR0208800DF0308800DR0308800DF0408800DR0408800DF0608800DR0608800DF0808800DR0808800DF1008800DR1008800DF1208800DR120

1.76 to 23.72.96 to 67.31.76 to 23.74.83 to 1582.96 to 67.37.96 to 2614.83 to 158.017.5 to 5767.96 to 261.030.2 to 99217.5 to 57668.5 to 225130.2 to 992119 to 3868.5 to 2251231 to 6144119 to 38391 to 8813231 to 6144

0.40 to 5.40.67 to 15.30.40 to 5.41.10 to 35.90.67 to 15.31.81 to 59.41.10 to 35.94.00 to 1301.81 to 59.36.86 to 2254.00 to 13015.6 to 5116.86 to 22527.0 to 88515.6 to 51152.2 to 139527.0 to 88588.8 to 200252.2 to 1395

(1)Table7 is a reference of flow rates that can be measured for the standard Rosemount 8800D and the reducer 8800DR Vortex Meters. It does not consider

density limitations, as described in tables 2 and 3.(2)Velocity range of the 8800DW is the same as 8800DF.

Flow-11

Product Data Sheet

Rosemount 8800D

TABLE 8. Air Flow Rate Limits at 59 °F (15 °C)

12maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

1200813-0100-4004, Rev FA

Catalog 2008 - 2009

79.27.8179.23.7279.22.8079.22.3479.22.3479.22.3473.02.3466.02.34

13413.31346.321344.751343.981343.981343.981243.981123.98

27.93.8627.91.3127.90.9827.90.8227.90.8227.90.8225.70.8223.00.82

47.36.57.32.2247.31.67.31.4147.31.4147.31.4143.91.4139.41.41

Not AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot Available

0 psig(0 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

27.93.8627.91.3127.90.9827.90.8227.90.8227.90.8225.70.8223.00.82

47.36.57.32.2247.31.67.31.4147.31.4147.31.4143.91.4139.41.41

Not AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot Available

TABLE 9. Air Flow Rate Limits at 59 °F (15 °C)

12maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

21218.42128.762126.582125.512125.511985.511725.511545.51

36031.236014.936011.23609.363609.363379.362939.362629.36

79.27.8179.23.7279.22.8079.22.3479.22.3479.22.3473.02.3466.02.34

13413.31346.321344.751343.981343.981343.981243.981123.98

34930.334914.534910.83499.093499.093269.092849.092549.09

59351.559324.659318.359315.459315.455415.448315.443215.4

21218.42128.762126.582125.512125.511985.511725.511545.51

36031.236014.936011.23609.363609.363379.362939.362629.36

0 psig(0 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

Flow-12

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

TABLE 10. Air Flow Rate Limits at 59 °F (15 °C)

maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

77066.877031.877023.977020.077020.071820.062520.056020.0

1308114130854.1130840.6130834.0130834.0122034.0106234.095134.0

34930.334914.534910.83499.093499.093269.092849.092549.09

59351.559324.659318.359315.459315.455415.448315.443215.4

1326115132654.81321.1132634.5132634.5123734.5107634.5934.5

2253195225393.2225369.8225358.6225358.6210258.6182858.6163858.6

77066.877031.877023.977020.077020.071820.062520.056020.0

1308114130854.1130840.6130834.0130834.0122034.0106234.095134.0

0 psig(0 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

TABLE 11. Air Flow Rate Limits at 59 °F (15 °C)

maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

30092613009124300993.3300978.2300978.2280778.2244278.2218878.2

51124435112211511215951121335112133476913341491333717133

1326115132654.81321.1132634.5132634.5123734.5107634.5934.5

2253195225393.2225369.8225358.6225358.6210258.6182858.6163858.6

521145252112155211162521113552111354862135422813637136

885376888533658853276885322988532298260229718322937229

30092613009124300993.3300978.2300978.2280778.2244278.2218878.2

51124435112211511215951121335112133476913341491333717133

0 psig(0 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

Flow-13

Product Data Sheet

Rosemount 8800D

TABLE 12. Air Flow Rate Limits at 59 °F (15 °C)

00813-0100-4004, Rev FA

Catalog 2008 - 2009

maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

8214712.98214339.58214254.78214213.68214213.676213.666213.65972213.6

139561211139565771395331395636313956363130213631132236310146363

521145252112155211162521113552111354862135422813637136

885376888533658853276885322988532298260229718322937229

11781102211781486.911781365.411781306.311781306.310992306.39559306.38565306.3

20016173620016827200166212001652020016520186755201624152014552520

8214712.98214339.58214254.78214213.68214213.676213.666213.65972213.6

139561211139565771395331395636313956363130213631132236310146363

0 psig(0 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

NOTES

The Rosemount 8800D measures the volumetric flow under operating conditions (i.e. the actual volume at the operating pressure and temperature–acfm or acmh), as shown above. However, gas volumes are strongly dependent on pressure and temperature. Therefore, gas quantities are typically stated in

standard or normal conditions (e.g. SCFM or NCMH). (Standard conditions are typically 59 °F and 14.7 psia. Normal conditions are typically 0 °C and 1 bar abs.)

The flow rate limits in standard conditions are found using the equations below:

Standard Flow Rate = Actual Flow Rate X Density Ratio

Density Ratio = Density at Actual (Operating) Conditions / Density at Standard Conditions

Flow-14

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

TABLE 13. Saturated Steam Flow Rate Limits (Assumes Steam Quality is 100%)

1215 psig(1,03 bar G)25 psig(1,72 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

12012.815814.025017.2923.160627.478231.2113537.6149244.1185554.8

54.65.8171.76.351138.0019410.527512.535414.151517.067620.084124.9

Not AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot AvailableNot Available

34234.844939.971150.1122165.7172478.1222588.7322910742441255277156

15515.820318.132222.755429.878235.4100940.21448.5192556.7239370.7

12012.815814.025017.2923.160627.478231.2113537.6149244.1185554.8

54.65.8171.76.351138.0019410.527512.535414.151517.067620.084124.9

TABLE 14. Saturated Steam Flow Rate Limits (Assumes Steam Quality is 100%)

1215 psig(1,03 bar G)25 psig(1,72 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

91782.0120493.91904118327015546161845956209842521136229514126367

41637.2542.6853.4148370.1209483.2270294.53921114515413407167

34234.844939.971150.1122165.7172478.1222588.7322910742441255277156

15515.820318.132222.755429.878235.4100940.21448.5192556.7239370.7

1511135198315531381955325576093039818344142484151872748723284605

68561.2970.2142388.3244411634511374453156631849422110561274

91782.0120493.91904118327015546161845956209842521136229514126367

41637.2542.6853.4148370.1209483.2270294.53921114515413407167

Flow-15

Product Data Sheet

Rosemount 8800D

TABLE 15. Saturated Steam Flow Rate Limits (Assumes Steam Quality is 100%)

00813-0100-4004, Rev FA

Catalog 2008 - 2009

15 psig(1,03 bar G)25 psig(1,72 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

333029843703416914429118745621676366821630759313914412581073512971334

151013519821553136195538625576033039811344142374151871448723267605

1511135198315531381955325576093039818344142484151872748723284605

68561.2970.2142388.3244411634511374453156631849422110561274

5734513752658711905739204468288661150372471307540521574710471847883342297

2601233341426754003359275439130935221655932451771432226838400681042

333029843703416914429118745621676366821630759313914412581073512971334

151013519821553136195538625576033039811344142374151871448723267605

TABLE 16. Saturated Steam Flow Rate Limits (Assumes Steam Quality is 100%)

15 psig(1,03 bar G)25 psig(1,72 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

130131163170801333270191670521976561126108453029651226663572161231922004685212

59035287747605122557602104999629761118438342134555016207313519019093123

5734513752658711905739204468288661150372471307540521574710471847883342297

2601233341426754003359275439130935221655932451771432226838400681042

22534201529575230846787290380356380411344045201463755134212411618527920072593471349025

102219141341510472122213173491725514552050663952329963482805126332931574574094

130131163170801333270191670521976561126108453029651226663572161231922004685212

59035287747605122557602104999629761118438342134555016207313519019093123

Flow-16

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

TABLE 17. Saturated Steam Flow Rate Limits (Assumes Steam Quality is 100%)

15 psig(1,03 bar G)25 psig(1,72 bar G)50 psig(3,45 bar G)100 psig(6, bar G)150 psig(10,3 bar G)200 psig(13,8 bar G)300 psig(20,7 bar G)400 psig(27,6 bar G)500 psig(34,5 bar G)

maxminmaxminmaxminmaxminmaxminmaxminmaxminmaxminmaxmin

35519317546618457073748457512666059961788087125230722809233481097494400851144254716514226

16111144021146207333452207557452272081106323210465436701518674422199619519024819053

22534201529575230846787290380356380411344045201463755134212411618527920072593471349025

102219141341510472122213173491725514552050663952329963482805126332931574574094

50994455466862521810577465621816638600255710218330915116074802031398363119511178477520404

231302066303282367479782976824013901116327463515010152652178166343286305744435596255

35519317546618457073748457512666059961788087125230722809233481097494400851144254716514226

16111144021146207333452207557452272081106323210465436701518674422199619519024819053

Rosemount 8800D

Flow-17

Rosemount 8800D

PERFORMANCE SPECIFICATIONS

The following performance specifications are for all Rosemount models except where noted. Digital performance specifications applicable to both Digital HART and FOUNDATION fieldbus output.

Flow Accuracy

Includes linearity, hysteresis, and repeatability.Liquids - for Reynolds Numbers over 20000Digital and Pulse Output±0.65% of rate

Note: The accuracy for the 8800DR, line sizes 6 to 12 in. (150 to 300mm), is ±1.0% of rate.Analog Output

Same as pulse output plus an additional 0.025% of span

Gas and Steam - for Reynolds Numbers over 15,000

Digital and Pulse Output±1.35% of rate

Note: The accuracy for the 8800DR, line sizes 6 to 12 in. (150 to 300mm), is ±1.50% of rate.Analog Output

Same as pulse output plus an additional 0.025% of span

Accuracy limitations for gas and steam:

For 1/2 and 1 in. (DN 15 and DN 25): max velocity of 220 ft/s (67.06 m/s)

For 1/2 to 8 in. (DN 15 to DN 200) Dual-style meters: max velocity of 100 ft/s (30.5 m/s)

NOTE

For 1/2 in. through 4 in. (15mm through 100mm) line sizes, as the meter Reynolds number decreases below the stated limit to 10000, the positive limit of the accuracy error band will increase to 2.1% for the pulse output. Example: +2.1% to –0.65% for liquids.Process Temperature Accuracy

2.2 °F (1.2 °C) or 0.4% of reading (in °C), whichever is greater.

NOTE

For remote mount installations, add ±0.018 °F/ft. (±0.03 °C/m) of uncertainty to the temperature measurement.

Flow-18

Product Data Sheet

00813-0100-4004, Rev FA

Catalog 2008 - 2009

Mass Flow Accuracy for Temperature Compensated Mass FlowDigital and Pulse Output± 2.0% of rate (Nominal)

Nominal conditions include temperature variation in saturation and superheat at 150 psig (10 bar-g) and above.

For pressure below 150 psig (10 bar-g), add 0.08% of uncertainty for every 15 psi (1 bar) below 150 psig (10 bar-g).

Analog Output

Same as pulse output plus an additional 0.025%ofspanRepeatability

± 0.1% of actual flow rateStability

± 0.1% of rate over one yearProcess Temperature Effect

Automatic K-factor correction with user-entered process temperature.

Table18 indicates the percent change in K-factor per 100 °F (55.5 °C) in process temperature from reference temperature of 77 °F (25 °C).

TABLE 18. Process Temperature Effect

316L @ < 77 °F (25 °C)+ 0.23316L @ > 77 °F (25 °C)- 0.27Nickel Alloy C < 77 °F (25 °C)+ 0.22Nickel Alloy C > 77 °F (25 °C)

- 0.22

Ambient Temperature EffectDigital and Pulse OutputsNo effect

Analog Output

±0.1% of span from –58 to 185 °F (–50 to 85 °C)

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Vibration Effect

An output with no process flow may be detected if sufficiently high vibration is present.

The meter design will minimize this effect, and the factory settings for signal processing are selected to eliminate these errors for most applications.

If an output error at zero flow is still detected, it can be eliminated by adjusting the low flow cutoff, trigger level, or low-pass filter.

As the process begins to flow through the meter, most vibration effects are quickly overcome by the flow signal. At or near the minimum liquid flow rate in a normal pipe mounted installation, the maximum vibration should be 0.087 in. (2,21mm) double amplitude displacement or 1g acceleration,

whichever is smaller. At or near the minimum gas flow rate in a normal pipe mounted installation, the maximum vibration should be 0.043 in. (1,09 mm) double amplitude displacement or 1/2 g acceleration, whichever is smaller.Mounting Position Effect

Meter will meet accuracy specifications when

mounted in horizontal, vertical, or inclinedpipelines. Best practice for mounting in a horizontal pipe is to orient the shedder bar in the horizontal plane. This will prevent solids in liquid applications and liquid in gas/steam applications from disrupting the shedding frequency. EMI/RFI Effect

Meets EMC requirements to EU Directive 2004/108/EC.

HART Analog

Output error less than ±0.025% of span with twisted pair from 80-1000 MHz for radiated field strength of 10 V/m. Tested per EN61326.Foundation fieldbus and Digital HART

No affect on the values that are being given if using HART digital signal or FOUNDATION fieldbus. Tested per EN61326.Magnetic-Field Interference

HART Analog

Output error less than ±0.025% of span at 30 A/m (rms); meets IEC 60770-1984, Section 6.2.9. Tested per EN61326.

Rosemount 8800D

Foundation fieldbus

No effect on digital output accuracy at 30 A/m (rms). Tested per EN 61326.Series Mode Noise Rejection

HART Analog

Output error less than ±0.025% of span at 1 V rms, 60 Hz; meets IEC 60770-1984, Section 6.2.4.2.

Foundation fieldbus

No effect on digital output accuracy at 1 V rms 60 Hz. Meets IEC 60770-1984, Section 6.2.4.2Common Mode Noise Rejection

HART Analog

Output error less than ±0.025% of span at

30Vrms, 60Hz; meets IEC 60770-1984, Section 6.2.4.1.

Foundation fieldbus

No effect on digital output accuracy at 250 V rms, 60 Hz. According to FF-830-PS-2.0 test case 8.2.Power Supply Effect

HART Analog

Less than 0.005% of span per voltFoundation fieldbusNo effect on accuracy.

Flow-19

Rosemount 8800D

PHYSICAL SPECIFICATIONS

NACE Compliance

Materials of Construction meet NACE material

recommendations per MR0175/ISO15156 for use in H2S containing environments in oil field production. Materials of construction also meet NACE

recommendations per MR0103-2003 for corrosive petroleum refining environments. MR0103

compliance requires Q25 option in model code.Electrical Connections

1/2 –14 NPT, PG 13.5, or M20 ϫ 1.5 conduit threads;

screw terminals provided for 4–20 mA and pulse output connections; communicator connections permanently fixed to terminal block.Non-Wetted Materials

Housing

Low-copper aluminum (FM Type 4X, CSA Type 4X, IP66)Paint

PolyurethaneCover O-ringsBuna-N

Flanges

316/316L lap joint

Temperature Sensor (MTA Option)Type-N Special Limits ThermocoupleProcess-Wetted Materials

Meter Body

316L wrought stainless and CF-3M cast stainless or N06022 wrought Nickel Alloy and CW2M

castNickel Alloy. Other material grades available. Consult factory for other materials of construction.Flanges

316/316L stainless steelNickel Alloy N06022 Weld NeckCollars

Nickel Alloy N06022

Surface Finish of Flanges and CollarsStandard: 125 to 250 μ inches (3.1 to 6.3 μ meters) Ra roughnessSmooth: 63 to 125 μ inches

(1.6 to 3.1 μ meters) Ra roughness

Flow-20

Product Data Sheet

00813-0100-4004, Rev FA

Catalog 2008 - 2009

Process Connections

Mounts between the following flangeconfigurations:ASME B16.5 (ANSI): Class 150, 300, 600, 900, 1500DIN: PN 10, 16, 25, 40, , 100, 160JIS: 10K, 20K, and 40K

Weld-end: Schedule 10, Schedule 40, Schedule 80, Schedule 160Mounting

Integral (Standard)

Electronics are mounted on meter body.Remote (Optional)

Electronics may be mounted remote from the meter body. Interconnecting coaxial cable

available in nonadjustable 10, 20, and 30 ft (3,0, 6,1, and 9,1 m) lengths. Consult factory for non-standard lengths up to 75 ft (22,9 m). Remotemounting hardware includes a

polyurethane painted, carbon steel pipe mount bracket with one carbon steel u-bolt.

Temperature Limitations for Integral MountingThe maximum process temperature for integral mount electronics is dependent on the ambient temperature where the meter is installed. The electronics must not exceed 185°F (85°C). The following is for reference, please note that the pipe was insulated with 3 inches of ceramic fiber insulator.

FIGURE 1. Rosemount 8800 Vortex Flowmeter

Ambient/process temperature limits

Shows combinations of ambient and process temperatures needed to remain at or below 185°F (85°C) housing temperature200 (93))C180 (82)°( F160 (71)° er140 (60)185°F Housing utTemperature ar120 (49)eLimitpm100 (38)Te t80 (27)neib60 (16)0)))))m)))))8394061728A3940617283(( 1223344500(((((((( 0 00000000012000000003456701Process Temperature °F (°C)Meter and pipe insulated with 3 inches of ceramic fiber insulation. Horizontal Pipe and Vertical meter position.Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Pipe Length Requirements

The vortex meter may be installed with a minimum of ten straight pipe diameters (D) upstream and five straight pipe diameters (D) downstream by following the K-factor corrections as described in the Technical Data Sheet (00816-0100-3250) on Installation Effects. No K-factor correction is required if 35 diameters upstream (35D) and 10 diameters downstream (10D) are available.Tagging

The flowmeter will be tagged at no charge, according to customer requirements. All tags are stainless steel. The standard tag is permanently attached to the flowmeter. Character height is 1/16 in. (1,6mm). A wired-on tag is available on request.Flow Calibration Information

Flowmeter calibration and configuration information is provided with every flowmeter. For a certified copy of flow calibration data, Option Q4 must be ordered in the model number.

Rosemount 8800D

Flow-21

Product Data Sheet

Rosemount 8800D

Product Certifications

Approved Manufacturing Locations

Rosemount Inc. — Eden Prairie, Minnesota, USA

Emerson Process Management BV - Ede, The Netherlands

00813-0100-4004, Rev FA

Catalog 2008 - 2009

EUROPEAN DIRECTIVE INFORMATION

The CE Declaration of Conformity for all applicable European directives for this product can be found on our website at

www.rosemount.com. A hard copy may be obtained by contacting our local sales office.

ATEX Directive

Rosemount Inc. complies with the ATEX Directive.

Flameproof enclosure EEx d protection type in accordance with EN50018

•Transmitters with Flameproof enclosure type protection shall only be opened when power is removed.

•Closing of entries in the device must be carried out using the appropriate EEx d metal cable gland or metal blanking plug. •Do not exceed the energy level, which is stated on the approval label.

Type n protection type in accordance with EN60079-15

Closing of entries in the device must be carried out using the appropriate EExe or EExn metal cable gland and metal blanking plug or any appropriate ATEX approved cable gland and blanking plug with IP66 rating certified by an EU approved certification body.

EUROPEAN PRESSURE EQUIPMENT DIRECTIVE (PED)

Rosemount 8800 Vortex Flowmeter Line Size 40 mm to 300 mm

Certificate Number PED-H-100

0575Module H Conformity Assessment

Mandatory CE-marking for flowmeters in accordance with Article 15 of the PED can be found on the flowtube body. Flowmeter categories I – IV, use module H for conformity assessment procedures.

Rosemount 8800 Vortex Flowmeter Line Size 15 mm and 25 mm

Sound Engineering Practice

Flowmeters that are SEP or Category I with Explosion-Proof

protection are outside the scope of PED and cannot be marked for compliance with PED.

Flow-22

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

HAZARDOUS LOCATION CERTIFICATIONS

Rosemount 8800D with HART ProtocolNorth American Certifications

Factory Mutual (FM)

Explosion-Proof for Class I, Division 1, Groups B, C, and D;Dust-ignition proof for Class II/III, Division 1, Groups E, F, and G;

Temp Code T6 (-50°C ≤ Ta ≤ 70°C)Conduit Seal not requiredEnclosure Type 4X.

Intrinsically safe for use in Class I, Division 1, Groups A, B, C, and D;

Class I, Zone 0, AEx ia IIC T4 (-50°C ≤ Ta ≤ 70°C);

Class II/III, Division 1, Groups E, F, and G locations when connected in accordance with Rosemount drawings 08800-0116;

Non-incendive for Class I, Division 2, Groups A, B, C, and D and Suitable for Class I, Division 2, Groups A, B, C, and D, with non-incendive field wiring (NIFW) when installed in accordance with Rosemount drawing 08800-0116;Temperature code T4 (-50°C ≤ Ta ≤ 70°C)Enclosure Type 4X.K5

E5 and I5 Combination

Canadian Standards Association (CSA)

Explosion-Proof for Class I, Division 1, Groups B, C, and D; Dust-ignition proof for Class II and Class III, Division 1, Groups E, F, and G; Temp Code T5 (TA = 70°C) Class I Zone1; Ex d (ia) T6 (-50°C ≤ Ta ≤ 70°C)

Suitable for Class I, Division 2, Groups A, B, C, and D; Temp Code T3C.Factory sealed.Enclosure Type 4X.

Intrinsically safe for Class I, Division 1, Groups A, B, C, and D; When connected in accordance with Rosemount drawing 08800-0112;

Temperature code T3CEnclosure Type 4X.K6

E6 and I6 Combination

Rosemount 8800D

European Certifications

ATEX Intrinsic Safety

Certification No. Baseefa05ATEX0084X ATEX Marking II 1 GEEx ia IIC T5 (-60°C ≤ Ta ≤ 40°C)EEx ia IIC T4 (-60°C ≤ Ta ≤ 70°C)Input Parameters:UI(1)i = 30 VDCi = 185 mAPi(1) = 1.0 WCi = 0 μFLi = 0.97 mH 0575SPECIAL CONDITIONS

When fitted with 90V transient suppressors (T1

Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

ATEX Type N Certification

Certification No. Baseefa05ATEX0085XATEX Marking II 3 GEEx nAnL II T5 (-40°C ≤ Ta ≤ 70°C)Input Parameters:Ui = 42 V dc MaxCi = 0 μFLi = 0.97 mH

SPECIAL CONDITIONS

When fitted with 90V transient suppressors (T1

Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

ATEX Flameproof Certification

Certification No. KEMA99ATEX3852X ATEX Marking Remote Mount:Transmitter: II 2(1) GEEx d [ia] IIC T6 (-50°C ≤ Ta ≤ 70°C)

Meter Body: II 1 G EEx ia IIC T6 (-50°C ≤ TATEX Marking Integral Mount: II 1/2 Ga ≤ 70°C)

EEx d [ia] IIC T6 (-50°C ≤ Ta ≤ 70°C)

0575V = 42 Vdc MaxUm = 250V

(1)Total for transmitter

Flow-23

Rosemount 8800D

SPECIAL CONDITIONS

When the equipment is installed, precautions must be taken to ensure, taking into account the effect of the fluid temperature, that the ambient temperature of the electrical parts of the equipment is comprised between -50°C and 70°C.

The remote mounted sensor may only be connected to the transmitter with the associated cable, supplied by the manufacturer. ATEX Dust Certification

Certification No. Baseefa05ATEX0086ATEX Marking II 1 D T90°C (-20°C ≤ Ta ≤ 70°C)

Ui = 42 V dc 0575K1

E1, I1, N1 and ND Combination

Flow-24

Product Data Sheet

00813-0100-4004, Rev FA

Catalog 2008 - 2009

International IECEx Certifications

Intrinsic Safety

Certification No. IECEx BAS05.0028X Ex ia IIC T5 (-60°C ≤ Ta ≤ 40°C)Ex ia IIC T4 (-60°C ≤ Ta ≤ 70°C)Input Parameters:UIi = 30 VDCPi = 185 mACi = 1.0 Wi = 0 μFLi = 0.97 mH

SPECIAL CONDITIONS

When fitted with 90V transient suppressors (T1

Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

Type N Certification

Certification No. IECEx BAS05.0029X Ex nC IIC T5 (-40°C ≤ Ta ≤ 70°C) Ui = 42 V dc

SPECIAL CONDITIONS

When fitted with 90V transient suppressors (T1

Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

Flameproof Certification

Certification No. IECEx KEM05.0017X Marking Remote Mount:

Transmitter: Ex d [ia] IIC T6 (-50°C ≤ Ta ≤ 70°C)Meter Body: Ex ia IIC T6 (-50°C ≤ Ta ≤ 70°C)Marking Integral Mount: Ex d [ia] IIC T6

(-50°C ≤ Ta ≤ 70°C)V = 42 Vdc MaxUm = 250V

SPECIALCONDITIONS

When the equipment is installed, particular

precautions must be taken to ensure, taking into account the effect of the process fluid temperature, that the ambient temperature of the electrical parts of the equipment is comprised between -50°Cand70°C.

The remote mounted sensor shall only be connected to the transmitter with the associated cable, supplied by the manufacturer.

E7, I7, and N7 Combination

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Chinese Certifications (NEPSI)

Flameproof Certification

Certification No. GYJ071327XEx dia IIC T6 (-50°C to 70°C)

Intrinsic Safety

Certification No. GYJ071171XEx ia IIC T4/T5T4: (-60°C to 70°C)T5: (-60°C to 40°C)Input Parameters:Ui = 30 VDCIi = 185 mA PCi = 1.0 Wi = 0 μFLi = 0.97 mH

Type N Certification

Certification No. GYJ071193XEx nAnL IIC T5 (-40°C to 70°C)42 VDC MaxK3

E3, I3, and N3 Combination

Japanese Certifications (TIIS)

Flameproof Certification

Transmitter - Ex d [ia] T6Remote Sensor - Ex ia IIC T6Certificate Description

TC17816 8800D with display, without MTA optionTC17817 8800D without display, without MTA optionTC17905 8800D with display, with MTA optionTC17906 8800D without display, with MTA option

Combination Certifications

E5, I5, E6, and I6 Combination

Rosemount 8800D

Flow-25

Rosemount 8800D

Rosemount 8800D With FOUNDATION Fieldbus Protocol

North American Certifications

Factory Mutual (FM) Approvals

Explosion-Proof for Class I, Division 1, Groups B, C, and D. Dust-Ignition proof for Class II/III, Division 1, Groups E, F, and G.

Temperature Code T6 (-50°C ≤ Ta ≤ 70°C)Conduit seal not required.Enclosure Type 4X

Intrinsically safe for use in Class I, Division 1, Groups A, B, C, and D;

Class I, Zone 0, AEx ia IIC T4 (-50°C ≤ Ta ≤ 40°C);

Class II/III, Division 1, Groups E, F, and G locations when connected in accordance with Rosemount drawings 08800-0116;

FISCO for Class I, Division 1, Groups A, B, C, and D. Class II/III, Division 1,Groups E, F, and G. Temp. Code: T4 (-50°C ≤ Ta ≤ 40°C)

when installed per Rosemount control drawing 08800-0116. K5

E5 and I5 combination

Canadian Standards Association (CSA) Approvals

Suitable for Class I, Division 2, Groups A, B, C, and D; Temp Code T3C.Factory sealed.Enclosure Type 4X.

Intrinsically Safe for Class I, Division 1, Groups A, B, C, and D;

When connected in accordance with Rosemount drawing 08800-0112;

Temperature Code T3C.Enclosure Type 4X

FISCO for Class I, Division 1, Groups A, B, C, and D;Temperature Code: T3C.

When installed per Rosemount drawing 08800-0112Enclosure Type 4XK6

E6 and I6 combination.

Flow-26

Product Data Sheet

00813-0100-4004, Rev FA

Catalog 2008 - 2009

European Certifications

ATEX Intrinsic Safety Certification

Certification No. Baseefa05ATEX0084XATEX Marking II 1 GEEx ia IIC T4 (-60°C ≤ Ta ≤ 60°C) 0575Input Parameters:Ui = 30 VDCIi = 300 mAPCi = 1.3 Wi = 0 μFLi = 20 μH

SPECIAL CONDITIONS FOR SAFE USE (X)When fitted with 90V transient suppressors (T1

Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

ATEX FISCO

Certification No. Baseefa05ATEX0084XATEX Marking II 1 G EEx ia IIC T4 (-60°C ≤ Ta ≤ 60°C) 0575Input Parameters:Ui = 17.5 VDCIPi = 380 mACi = 5.32 Wi = 0 μFLi < 10 μH

SPECIAL CONDITIONS FOR SAFE USE (X)When fitted with 90V transient suppressors (T1

Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

ATEX Type N Certification

Certification No. Baseefa05ATEX0085XATEX Marking II 3 GEEx nAnL IIC T5 (-40°C ≤ Ta ≤ 70°C)Input Parameters:Ui = 42 VDC MAXCi = 0 μFLi = 20 μH

SPECIAL CONDITIONS FOR SAFE USE (X)When fitted with 90V transient suppressors (T1

Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

ATEX Flame-Proof Certifications

Certification No. KEMA 99ATEX3852X ATEX Marking Remote Mount:Transmitter: II 2(1) GEEx d [ia]IIC T6 (-50°C ≤ Ta ≤ 70°C)

Meter Body: II 1 G EEx ia IIC T6 (-50°C ≤ Ta ≤ 70°C)

ATEX Marking Integral Mount: II 1/2 GEEx d [ia] IIC T6 (-50°C ≤ Ta ≤ 70°C) 0575V = 42 Vdc MaxUm = 250V

SPECIALCONDITIONS

When the equipment is installed, particular

The remote mounted sensor shall only be connected to the transmitter with the associated cable, supplied by the manufacturer.

ATEX Dust Certification

Certification No. Baseefa05ATEX0086ATEX Marking II 1 D T90°C (-20°C ≤ Ta ≤ 70°C) Ui = 42 VDC 0575K1

E1, I1, N1 and ND Combination

Rosemount 8800D

International IECEx Certifications

Intrinsic Safety

Certification No. IECEx BAS 05.0028X Ex ia IIC T4 (-60°C ≤ Ta ≤ 60°C)Input Parameters:Ui = 30 VDCIi = 300 mAPCi = 1.3 Wi = 0 μFLi = 20 μH

SPECIAL CONDITIONS

When fitted with 90V transient suppressors (T1

Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

FISCO

Certification No. IECEx BAS 05.0028X Ex ia IIC T4 (-60°C ≤ Ta ≤ 60°C)Input Parameters:UI = 380 mAi = 17.5 VDCPiCi = 5.32 Wi = 0 μFLi < 10 μH

Type N Certification

Certification No. IECEx BAS 05.0029X Ex nC IIC T5 (-40°C ≤ Ta ≤ 70°C)Ui = 42 V dc

Flameproof Certification

Certification No. IECEx KEM 05.0017X Marking Remote Mount:

Transmitter: Ex d [ia] IIC T6 (-50°C ≤ T≤ Ta ≤ 70°C)Meter Body: Ex ia IIC T6 (-50°C a ≤ 70°C)Marking Integral Mount: Ex d [ia] IIC T6

(-50°C ≤ Ta ≤ 70°C)V = 42 Vdc MaxUm = 250V

SPECIALCONDITIONS

When the equipment is installed, particular

The remote mounted sensor shall only be connected to the transmitter with the associated cable, supplied by the manufacturer.

E7, I7, and N7 Combination

Flow-27

Product Data Sheet

Rosemount 8800D

Chinese Certifications (NEPSI)

Flameproof Certification

Certification No. GYJ071327XEx dia T6 (-50°C to 70°C)

00813-0100-4004, Rev FA

Catalog 2008 - 2009

Intrinsic Safety

Certification No. GYJ071171XEx ia IIC T6 (-60°C to 60°C)Input Parameters:Ui = 30 VDCIi = 300 mAPi = 1.3 WCi = 0 μFLi = 20 μH

FISCO/FNICO

For FISCO:

Certification No. GYJ071171XEx ia IIC T4 (-60°C to 60°C)Input Parameters:Ui = 17.5 VDCIi = 380 mAPi = 5.32 WCi = 0 μFLi < 10 μHFor FNICO:

Certification No. GYJ071193XEx nAnL IIC T5 (-40°C to 70°C)17.5 VDC Max

Type N Certification

Certification No. GYJ071193XEx nAnL IIC T5 (-40°C to 70°C)32 VDC MaxK3

E3, I3, and N3 Combination

Japanese Certifications (TIIS)

Flameproof CertificationE4 TIIS Flameproof

Transmitter - Ex d [ia] T6Remote Sensor - Ex ia IIC T6Certificate Description

TC17816 8800D with display, without MTA optionTC17817 8800D without display, without MTA option

Combination Certifications

E5, I5, E6, and I6 Combination

Flow-28

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

Dimensional Drawings

FIGURE 2. Flanged-Style Flowmeter Dimensional Drawings (1/2-through 12 in./15 through 300 mm Line Sizes)Terminal Cover3.20 (81)2.56 (65)1.10 (28)Diameter 3.06 (78)2.85 (72)1.00 (25)Display OptionDiameter BDiagram illustrated without MTA Option2.00 (51)Diagram illustrated with MTA Option2.00 (51)CCDANOTEDimensions are in inches (millimeters)AFlow-29

Product Data Sheet

Rosemount 8800D

TABLE 19. Flanged-Style Flowmeter (1/2-through 2in./15 through 50 mm Line Sizes)

½ (15)Class 150Class 300Class 600Class 900PN 16/40PN 100JIS 10K/20KJIS 40KClass 150Class 300Class 600Class 900Class 1500PN 16/40PN 100PN 160JIS 10K/20KJIS 40KClass 150Class 300Class 600Class 900Class 1500PN 16/40PN 100PN 160JIS 10K/20KJIS 40KClass 150Class 300Class 600Class 900Class 1500PN 16/40PN PN 100PN 160JIS 10KJIS 20KJIS 40K

6.9 (175)7.2 (183)7.7 (196)8.4 (213)6.1 (155)6.6 (168)6.3 (160)7.3 (185)7.5 (191)8.0 (203)8.5 (216)9.4 (239)9.4 (239)6.3 (160)7.7 (195)7.7 (195)6.5 (165)7.9 (200)8.2 (208)8.7 (221)9.4 (239)10.4 (2)10.4 (2)6.9 (175)8.2 (208)8.4 (213)7.3 (185)8.5 (215)9.3 (236)9.8 (249)10.5 (267)12.8 (325)12.8 (325)8.0 (203)9.2 (234)9.6 (244)10.2 (259)7.7 (195)8.3 (210)9.8 (249)

–7.7 (196)7.7 (196)8.4 (213)

––––8.0 (203)8.5 (216)8.5 (216)9.4 (239)9.4 (239)

–––––8.7 (221)9.2 (234)9.4 (239)10.4 (2)10.4 (2)

–––––9.8 (249)10.4 (2)10.7 (271)12.9 (328)12.9 (328)

–––––––

0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.79 (45,5)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)

7.6 (193)7.6 (193)7.6 (193)7.6 (193)7.6 (193)7.6 (193)7.6 (193)7.6 (193)7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)

00813-0100-4004, Rev FA

Catalog 2008 - 2009

9.1 (4,1)10.4 (4,7)10.8 (4,9)15.3 (6,9)10.4 (4,7)12.3 (5,6)10.1 (4,5)13.5 (6,1)12.3 (5,6)15.0 (6,8)15.8 (7,2)24.3 (11,0)24.3 (11,0)13.5 (6,1)19.5 (8,8)19.5 (8,8)13.7 (6,2)17.4 (7,9)17.6 (8,0)23.0 (10,4)25.3 (11,5)36.3 (16,5)36.6 (16,6)19.3 (8,8)27.9 (12,7)29.3 (13,3)18.6 (8,4)25.6 (11,6)22.0 (10,0)26.0 (11,8)29.6 (13,4)59.4 (26,9)59.4 (26,9)23.0 (10,4)30.6 (13,9)36.4 (16,5)38.7 (17,6)19.5 (8,8)20.1 (9,1)28.3 (12,8)

1 (25)

1 ½ (40)2 (50)

4.7 (119)4.7 (119)4.7 (119)4.7 (119)

–4.7 (119)4.7 (119)4.7 (119)

(1)±0.14 in. (3.6 mm)(2)±0.03 in. (0.8 mm)(3)±0.20 in. (5.1 mm)

(4)Add 0.2 lb (0,1 kg) for display option

Flow-30

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

TABLE 20. Flanged-Style Flowmeter (3-through 6 in./80 through 150mm Line Sizes) (Refer to previous drawing)

3 (80)Class 150Class 300Class 600Class 900Class 1500PN 16/40PN PN 100PN 160JIS 10KJIS 20KJIS 40KClass 150Class 300Class 600Class 900Class 1500PN 16PN 40PN PN 100PN 160JIS 10KJIS 20KJIS 40KClass 150Class 300Class 600Class 900Class 1500PN 16PN 40PN PN 100JIS 10KJIS 20KJIS 40K

9.9 (251)10.6 (269)11.4 (290)12.9 (328)14.1 (358)8.9 (226)10.0 (254)10.5 (267)11.2 (284)7.9 (200)9.3 (235)11.0 (280)10.3 (262)11.0 (279)12.8 (325)13.8 (351)14.5 (368)8.4 (213)9.4 (239)10.4 (2)11.3 (287)12.1 (307)8.7 (220)8.7 (220)11.8 (300)11.6 (295)12.4 (315)14.3 (363)16.1 (409)18.6 (472)8.9 (226)10.5 (267)12.1 (307)13.7 (348)10.6 (270)10.6 (270)14.2 (360)

10.4 (2)11.2 (284)11.5 (292)13.0 (330)14.2 (361)

–––––––

10.8 (274)11.6 (295)12.9 (328)13.9 (353)14.6 (371)

––––––––

12.1 (307)13.0 (330)14.5 (368)16.2 (411)18.8 (478)

–––––––

2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.66 (67,6)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.43 (87,1)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.14 (130,6)5.14 (130,6)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)

9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)

5.3 (134)5.3 (134)5.3 (134)5.3 (134)

–5.3 (134)5.3 (134)5.3 (134)

–5.3 (134)5.3 (134)5.3 (134)5.9 (149)5.9 (149)5.9 (149)5.9 (149)

–5.9 (149)5.9 (149)5.9 (149)5.9 (149)

–5.9 (149)5.9 (149)5.9 (149)7.4 (187)7.4 (187)7.4 (187)

––7.4 (187)7.4 (187)7.4 (187)7.4 (187)7.4 (187)7.4 (187)7.4 (187)

36.9 (16,7)46.1 (20,9)52.1 (26,6)75.5 (34,2)105.8 (48,0)36.3 (16,5)45.1 (20,5)54.4 (24,7)59.6 (27,0)27.6 (12,5)35.0 (15,9)50.0 (22,7)50.7 (23,0)70.8 (32,1)96.5 (43,8)119.7 (54,3)157.9 (71,6)40.1 (18,2)49.2 (22,3)62.1 (28,2)78.5 (35,6)85.8 (38,9)37.0 (16,8)44.9 (20,4)75.3 (34,2)90.0 (40,8)129.5 (58,7)195.5 (88,7)253.7 (115,1)376.0 (170.6)75.6 (34,3)95.3 (43,2)138.8 (63,0)168.5 (76,4)79.8 (36,2)97.7 (44,3)175.9 (79,8)

4 (100)

6 (150)(1)±0.14 in. (3.6 mm)(2)±0.03 in. (0.8 mm)(3)±0.20 in. (5.1 mm)

(4)Add 0.2 lb (0,1 kg) for display option.

Flow-31

Product Data Sheet

Rosemount 8800D

00813-0100-4004, Rev FA

Catalog 2008 - 2009

TABLE 21. Flanged-Style Flowmeter (8-through 12 in./200 through 300mm Line Sizes) (Refer to previous drawing)

8 (200)Class 150Class 300Class 600Class 900Class 1500PN 10PN 16PN 25PN 40PN PN 100JIS 10KJIS 20KJIS 40KClass 150Class 300Class 600PN 10PN 16PN 25PN 40PN PN 100JIS 10KJIS 20KJIS 40KClass 150Class 300Class 600PN 10PN 16PN 25PN 40PN PN 100JIS 10KJIS 20KJIS 40K

13.6 (345)14.3 (363)16.6 (422)18.8 (478)22.8 (579)10.5 (266)10.5 (266)11.9 (302)12.5 (318)14.2 (361)15.8 (401)12.2 (310)12.2 (310)16.5 (420)14.6 (371)15.8 (401)19.1 (485)11.9 (302)12.1 (307)13.5 (343)14.8 (376)16.4 (417)18.9 (480)14.6 (371)14.6 (371)18.1 (460)16.8 (427)18.0 (457)20.5 (521)13.2 (335)13.9 (353)15.0 (381)16.9 (429)18.8 (478)21.2 (538)15.7 (399)15.7 (399)19.7 (500)

14.1 (358)15.0 (381)16.7 (424)19.0 (483)23.2 (5)

–––––––––

15.1 (384)16.4 (417)19.2 (488)

–––––––––

17.3 (439)18.7 (475)20.7 (526)

–––––––––

7.55 (191,8)7.55 (191,8)7.55 (191,8)6.62 (168,1)6.62 (168,1)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)

11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)

8.3 (210)8.3 (210)8.3 (210)

––8.3 (210)8.3 (210)8.3 (210)8.3 (210)8.3 (210)8.3 (210)8.3 (210)8.3 (210)8.3 (210)9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)

139.6 (63,3)196.2 (,0)295.0 (133,8)420.4 (190,7)6.0 (293,0)109.6 (49,7)108.5 (49,2)136.3 (61,8)154.8 (70,2)214.6 (97,3)279.9 (127)109.9 (49,9)134.3 (60,9)255.7 (116)197.2 ()285.2 (129)475.3 (216)156.3 (71)161.1 (73)197.4 (90)245.3 (111)306.3 (139)443.0 (201)173.3 (79)220.5 (100)377.3 (171)296.0 (134)413.2 (187)592.2 (269)203.1 (92)223.4 (101)267.8 (121)345.7 (157)428.5 (194)0.8 (291)224.5 (102)287.1 (130)504.7 (229)

10 (250)

12 (300)(1)±0.14 in. (3.6 mm)(2)±0.03 in. (0.8 mm)(3)±0.20 in. (5.1 mm)

(4)Add 0.2 lb (0,1 kg) for display option.

Flow-32

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

FIGURE 3. Rosemount 8800DR Reducer™ Flowmeter Dimensional Drawings (1-through 12 in./25 through 300 mm Line Sizes)

3.20 (81)2.85 (72)2.56 1.10 Terminal Cover(65)(28)Diameter3.06 (78)1.00 (25)DisplayOptionDiameter BDiagram illustrated without MTA Option

Diagram illustrated with MTA Option

2.00 2.00 (51)(51)CCDAANOTE

Dimensions are in inches (millimeters)

Flow-33

Product Data Sheet

Rosemount 8800D

TABLE 22. Reducer Flowmeter (1-through 3in./25 through 80 mm Line Sizes)1 (25)

Class 150Class 300Class 600Class 900PN 16/40PN 100PN 160Class 150Class 300Class 600Class 900PN 16/40PN 100PN 160Class 150Class 300Class 600Class 900PN 16/40PN PN 100PN 160Class 150Class 300Class 600Class 900PN 16/40PN PN 100PN 1607.5 (191)8.0 (203)8.5 (216)9.4 (239)6.3 (160)7.7 (195)7.7 (195)8.2 2088.7 (221)9.4 (239)10.4 (2)6.9 (175)8.2 (208)8.4 (213)9.3 (236)9.8 (249)10.5 (267)12.8 (325)8.0 (203)9.2 (234)9.6 (24410.2 (259)9.9 (251)10.6 (269)11.4 (290)12.9 (328)8.9 (226)10.0 (254)10.5 (267)11.2 (284)8.0 (203)8.5 (216)8.5 (216)9.4 (239)–––

00813-0100-4004, Rev FA

Catalog 2008 - 2009

0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)7.6 (193)7.6 (193)7.6 (193)7.6 (193)7.6 (193)7.6 (193)7.6 (193)7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)––––––––––––––––––––––

11.56 (5,24)14.22 (6,45)15.11 (6,85)20.70 (9.40)12. (5,73)18.44 (8,36)18.44 (8,36)15.81 (7,17)21.20 (9,62)23.77 (10,78)34.98 (15,87)17.50 (7,94)26.20 (11,88)27.67 (12,55)22.61 (10,26)26.76 (12,14)30.59 (13,88)60.76 (27,56)23.52 (10,67)31.28 (14,19)37.25 (16,90)39. (17,98)33.15 (15,04)42.66 (19,35)49.46 (22,43)73.28 (33,24)33.30 (15,10)42.45 (19,25)52.21 (23,68)57.94 (26,28)1 ½ (40)8.7 (221)9.2 (234)9.4 (239)10.4 (2)

–––

2 (50)

9.8 (249)10.4 (2)10.7 (271)12.9 (328)––––

3 (80)

10.4 (2)11.2 (284)11.5 (292)13.0 (330)––––4.7 (119)4.7 (119)4.7 (119)4.7 (119)4.7 (119)4.7 (119)4.7 (119)4.7 (119)(1)±0.14 in. (3.6 mm)(2)±0.03 in. (0.8 mm)(3)±0.20 in. (5.1 mm)

(4)Add 0.2 lb (0,1 kg) for display option.

Flow-34

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

TABLE 23. Reducer Flowmeter (4-through 12 in./100 through 300mm Line Sizes) (Refer to previous drawing)4 (100)

Class 15010.3 (262)10.8 (274)2.87 (72,9)9.1 (231)5.3 (134)46.33 (21,01)Class 30011.0 (279)11.6 (295)2.87 (72,9)9.1 (231)5.3 (134)67.04 (30,41)Class 60012.8 (325)12.9 (328)2.87 (72,9)9.1 (231)5.3 (134)94.26 (42,76)Class 90013.8 (351)13.9 (353)2.87 (72,9)9.1 (231)5.3 (134)118.04 (53,54)PN 168.4 (213)–2.87 (72,9)9.1 (231)5.3 (134)36.36 (16,49)PN 409.4 (239)–2.87 (72,9)9.1 (231)5.3 (134)45. (20,81)PN 10.4 (2)–2.87 (72,9)9.1 (231)5.3 (134)59.72 (27,09)PN 10011.3 (287)–2.87 (72,9)9.1 (231)5.3 (134)76.73 (34,80)PN 16012.1 (307)–

2.87 (72,9)9.1 (231)–84.73 (38,43)6 (150)Class 15011.6 (295)12.1 (307)3.79 (96,3)9.6 (244)5.9 (149)70.27 (31,87)Class 30012.4 (31513.0 (330)3.79 (96,3)9.6 (244)5.9 (149)113.09 (51,30)Class 60014.3 (363)14.5 (368)3.79 (96,3)9.6 (244)5.9 (149)185.13 (83,97)Class 90016.1 (409)16.2 (411)

3.79 (96,3)9.6 (244)5.9 (149)246.33 (111,73)PN 168.9 (226)–3.79 (96,3)9.6 (244)5.9 (149)59.20 (26,85)PN 4010.5 (267)–3.79 (96,3)9.6 (244)5.9 (149)81.94 (37,17)PN 12.1 (307)–3.79 (96,3)9.6 (244)5.9 (149)125.36 (56,86)PN 10013.7 (348)–3.79 (96,3)9.6 (244)5.9 (149)

162.29 (73,61)PN 16014.7 (373)–3.79 (96,3)9.6 (244)–187.91 (85,23)8 (200)

Class 15013.6 (345)14.1 (358)5.70 (144,8)10.8 (274)7.4 (187)133.14 (60,39)Class 30014.3 (363)15.0 (381)5.70 (144,8)10.8 (274)7.4 (187)195.54 (88,69)Class 60016.6 (422)16.7 (424)

5.70 (144,8)10.8 (274)7.4 (187)305.18 (138,43)PN 1010.5 (266)–5.70 (144,8)10.8 (274)7.4 (187)100.92 (45,78)PN 1610.5 (266)–5.70 (144,8)10.8 (274)7.4 (187)100.92 (45,78)PN 2511.9 (302)–5.70 (144,8)10.8 (274)7.4 (187)134.05 (60,80)PN 4012.5 (318)–5.70 (144,8)10.8 (274)7.4 (187)155.00 (70,31)PN 14.2 (361)–5.70 (144,8)10.8 (274)7.4 (187)220.68 (100,10)PN 10015.8 (401)–

5.70 (144,8)10.8 (274)7.4 (187)292.93 (132,87)10 (250)Class 15014.6 (371)15.1 (384)7.55 (191,8)11.7 (297)8.3 (210)182.45 (82,76)Class 30015.8 (401)16.4 (417)7.55 (191,8)11.7 (297)8.3 (210)281.66 (127,76)Class 60019.1 (485)19.2 (488)7.55 (191,8)11.7 (297)8.3 (210)4. (222,21)PN 1011.9 (302)–7.55 (191,8)11.7 (297)8.3 (210)138.63 (62,88)PN 1612.1 (307)–7.55 (191,8)11.7 (297)8.3 (210)148.58 (67,39)PN 2513.5 (343)–7.55 (191,8)11.7 (297)8.3 (210)191.00 (86,)PN 4014.8 (376)–7.55 (191,8)11.7 (297)8.3 (210)245.85 (111,52)PN 16.4 (417)–7.55 (191,8)11.7 (297)8.3 (210)314.13 (142,49)PN 10018.9 (480)–7.55 (191,8)11.7 (297)8.3 (210)463.49 (210,24)12 (300)

Class 15016.8 (427)17.3 (439)9.56 (242,8)12.8 (325)9.3 (236)281.98 (127,90)Class 30018.0 (457)18.7 (475)9.56 (242,8)12.8 (325)9.3 (236)412.18 (186,96)Class 60020.5 (521)20.7 (526)

9.56 (242,8)12.8 (325)9.3 (236)609. (296,)PN 1013.2 (335)–9.56 (242,8)12.8 (325)9.3 (236)188.28 (85,40)PN 1613.9 (353)–9.56 (242,8)12.8 (325)9.3 (236)211.79 (96,07)PN 2515.0 (381)–9.56 (242,8)12.8 (325)9.3 (236)262.45 (119,05)PN 4016.9 (429)–9.56 (242,8)12.8 (325)9.3 (236)349.92 (158,72)PN 18.8 (478)–9.56 (242,8)12.8 (325)9.3 (236)444.21 (201,49)PN 100

21.2 (538)

–

9.56 (242,8)

12.8 (325)

9.3 (236)

672.07 (304,85)

(1)±0.14 in. (3.6 mm)(2)±0.03 in. (0.8 mm)(3)±0.20 in. (5.1 mm)

(4)Add 0.2 lb (0,1 kg) for display option.

Flow-35

Product Data Sheet

Rosemount 8800D

3.20 (81)2.56 (65)1.10 (28)00813-0100-4004, Rev FA

Catalog 2008 - 2009

FIGURE 4. Wafer-Style Dimensional Drawings (1/2-through 8 in./15 through 200 mm Line Sizes)

2.00 (51)2.00 (51)Terminal Cover2.85 (72)1.00 (25)Diameter3.06 (78)DisplayOptionCDiameter DEANOTEDimensions are in inches (millimeters)Electronics housing may be rotated in 90 degree incrementsDiameter B TABLE 24. Rosemount 8800D Wafer-Style Meter

in. (mm)½ (15)1 (25)1½ (40)2 (50)3 (80)4 (100)6 (150)8 (200)

(1)±0.04 in. (1.0 mm)(2)±0.03 in. (0.8 mm)(3)±0.20 in. (5.1 mm)

(4)Add 0.2 lb (0,1 kg) for display option.

Face-to-face Ain. (mm)(1)2.56 (65)2.56 (65)2.56 (65)2.56 (65)2.56 (65)3.42 (87)4.99 (127)6.60 (168)

Diameter Bin. (mm)(2)0.54 (13,7)0.95 (24,1)1.49 (37,8)1.92 (49)2.87 (73)3.79 (96)5.70 (145)7.55 (192)

in. (mm)(3)7.63 (194)7.74 (197)8.14 (207)8.85 (225)9.62 (244)10.48 (266)10.75 (273)11.67 (296)

Diameter Din. (mm)1.38 (35,1)1.98 (50,3)2.87 (72,9)3.86 (98)5.00 (127)6.20 (158)8.50 (216)10.62 (270)

Ein. (mm)0.23 (5,9)0.23 (5,9)0.18 (4,6)0.12 (3)0.25 (6)0.44 (11)1.11 (28)0. (23)

Weightlb (kg)(4)7.3 (3,3)7.4 (3,4)10.0 (4,5)10.6 (4,8)13.6 (6,2)21.4 (9,7)49.1 (22,3)85 (38,6)

Flow-36

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

FIGURE 5. Vortex Dual-Sensor Style Flowmeter Dimensional Drawings (6 - 8 in (150 - 200mm) with 900# or 1500# flanges. See Figure 6.)

3.20 Terminal Cover(81)2.56 2.00 2.00 1.10 (65)2.85 (72)(51)(51)(28)3.06 (78)1.00 (25)Display OptionCDiameter BCNOTE Dimensions are in inches (millimeters)AFIGURE 6. Vortex Dual-Sensor Style Flowmeter Dimensional Drawings

(6 - 8 in (150 - 200mm) with 900# or 1500# flanges and all 10 - 12 in. (250-300mm) line sizes)

3.20 2.00 2.00 (81)1.10 (28)(51)(51)2.56 2.85 (65)(72)Terminal Cover3.06 (78)1.00 (25)Display OptionCCDiameter BNOTE Dimensions are in inches (millimeters)AFlow-37

Product Data Sheet

Rosemount 8800D

TABLE 25. Vortex Dual-Sensor Style Flowmeter (1/2-through 3 in./15 through 80 mm Line Sizes)

12.0 (305)12.3 (312)12.8 (325)13.5 (343)11.2 (284)11.8 (300)11.4 (290)12.4 (315)15.1 (384)15.6 (396)16.1 (409)17.0 (432)17.0 (432)13.9 (353)15.3 (3)15.3 (3)14.1 (358)15.5 (394)11.3 (287)11.8 (300)12.5 (318)13.5 (343)13.5 (343)10.0 (254)11.3 (287)11.5 (292)10.4 (2)11.5 (292)13.0 (330)13.6 (345)14.3 (363)16.6 (422)15.6 (396)11.8 (300)12.9 (328)13.4 (340)14.0 (356)11.5 (292)12.1 (307)13.6 (345)14.3 (363)15.0 (381)15.8 (401)17.3 (439)18.5 (470)13.4 (340)14.5 (367)14.9 (378)15.6 (396)12.3 (312)13.7 (348)15.5 (394)

–12.8 (325)12.8 (325)13.5 (343)

––––

15.6 (396)16.1 (409)16.1 (409)17.0 (432)17.0 (432)

–––––11.8 (300)12.3 (312)12.5 (318)13.5 (343)13.5 (343)

–––––

13.6 (345)14.1 (358)14.3 (363)16.7 (424)15.7 (399)

–––––––

14.8 (376)15.7 (399)15.8 (401)17.4 (442)18.6 (472)

–––––––

0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.67 (42.4)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.60 (66.0)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)

00813-0100-4004, Rev FA

Catalog 2008 - 2009

16.2 (7,4)17.4 (7,9)17.9 (8,1)22.4 (10.2)17.2 (7,8)19.2 (8,7)17.1 (7,8)20.6 (9,3)19.8 (9,0)22.5 (10,2)23.3 (10,6)31.8 (14,4)31.8 (14,4)21.0 (9,5)27.0 (12,3)27.0 (12,3)22.1 (10,0)25.8 (11,7)27.0 (12,3)32.4 (14,7)34.8 (15,8)45.7 (20,7)45.7 (20,7)28.7 (13,0)37.4 (17,0)38.8 (17,6)27.9 (12,6)34.9 (15,8)31.9 (14,5)35.9 (16,3)39.5 (17,9)69.2 (31,4)72.0 (32.6)32.9 (14,9)40.5 (18,4)46.2 (21,0)48.5 (22,0)29.1 (13,2)29.7 (13,5)37.9 (17,2)50.3 (22,8)59.5 (27,0)65.5 (29,7)88.9 (40,3)123.0 (55.8)49.7 (22,5)58.5 (26,5)67.8 (30,8)73.0 (33,1)41.0 (18,6)48.4 (22,0)63.4 (28,8)

1 (25)

1 ½ (40)2 (50)

3 (80)(1)±0.14 in. (3.6 mm)(2)±0.03 in. (0.8 mm)(3)±0.20 in. (5.1 mm)

(4)Add 0.4 lb (0,2 kg) for display option.

Flow-38

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

TABLE 26. Vortex Dual-Sensor Style Flowmeter (4- through 12 in./100 through 300 mm Line Sizes)

4 (100)Rosemount 8800D

15.2 (386)16.0 (406)17.7 (450)18.7 (475)20.0 (509)13.3 (338)14.4 (366)15.4 (391)16.3 (414)17.1 (434)13.6 (345)13.6 (345)16.8 (427)19.4 (493)20.2 (513)22.2 (5)16.1 (409)18.6 (472)16.8 (427)18.3 (465)19.9 (505)21.5 (546)18.5 (470)18.5 (470)22.0 (559)24.0 (610)24.8 (630)27.0 (686)18.4 (467)22.8 (580)20.9 (531)20.9 (531)22.3 (566)22.9 (582)24.7 (627)26.3 (668)22.6 (574)22.6 (574)27.0 (686)14.6 (371)15.8 (401)19.1 (485)11.9 (302)12.1 (307)13.5 (343)14.8 (376)16.4 (417)18.9 (480)14.6 (371)14.6 (371)18.1 (460)16.8 (427)18.0 (457)20.5 (521)13.2 (335)13.9 (353)15.0 (381)16.9 (429)18.8 (478)21.2 (538)15.7 (399)15.7 (399)19.7 (500)

Class 150Class 300Class 600Class 900Class 1500PN 16PN 40PN PN 100PN 160JIS 10KJIS 20KJIS 40KClass 150Class 300Class 600Class 900Class 1500PN 16PN 40PN PN 100JIS 10KJIS 20KJIS 40KClass 150Class 300Class 600Class 900Class 1500PN 10PN 16PN 25PN 40PN PN 100JIS 10KJIS 20KJIS 40KClass 150Class 300Class 600PN 10PN 16PN 25PN 40PN PN 100JIS 10KJIS 20KJIS 40KClass 150Class 300Class 600PN 10PN 16PN 25PN 40PN PN 100JIS 10KJIS 20KJIS 40K

15.7 (399)16.6 (422)17.7 (450)18.9 (480)20.2 (512)

––––––––

19.9 (505)20.8 (528)22.3 (566)16.2 (411)18.8 (478)

–––––––

24.5 (622)25.4 (5)27.1 (688)19.0 (483)23.2 (5)

–––––––––

15.1 (384)16.4 (417)19.2 (488)

–––––––––

17.3 (439)18.7 (475)20.7 (526)

–––––––––

3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.40 (86.4)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.14 (130.6)5.14 (130.6)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)6.62 (168,1)6.62 (168,1)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)11.38 (2)

9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)

68.1 (30,9)88.2 (40,0)113.9 (51,7)137.1 (62,2)182 (82.6)57.6 (26,1)66.6 (30,2)79.6 (36,1)95.9 (43,5)103.2 (46,8)55.4 (25,1)63.2 (28,7)93.7 (42,5)126.4 (57,3)165.9 (75,3)231.9 (105,2)266 (120.6)378 (171.4)112.0 (50,8)131.7 (59,7)175.2 (79,5)204.8 (92,9)124.0 (56,2)141.9 (,4)220.1 (99,8)190.1 (86,2)246.7 (111,9)345.5 (156,7)479 (217.3)637 (288.9)160.2 (72,7)159.0 (72,1)186.9 (83,4)205.4 (93,2)265.1 (120,2)330.4 (149,9)178.2 (80,8)202.6 (91,9)324.0 (147,0)201.5 (91)2.5 (131)479.6 (218)160.6 (73)165.4 (75)210.7 (96)249.6 (113)310.6 (141)447.3 (203)177.6 (81)224.8 (102)381.6 (173)300.3 (136)417.5 (1)596.5 (271)207.4 (94)227.7 (103)272.1 (123)350.0 (159)432.8 (196)5.1 (293)228.8 (104)291.4 (132)508.9 (231)

6 (150)8 (200)10 (250)12 (300)(1)±0.14 in. (3.6 mm)(2)±0.03 in. (0.8 mm)(3)±0.20 in. (5.1 mm)

(4)Add 0.4 Lb (0,2 kg) for display option.

Flow-39

Product Data Sheet

Rosemount 8800D

FIGURE 7. Vortex weld-end style flowmeter dimensional drawings

(1/2 - 4 in. (15 - 100 mm) line sizes)Terminal Cover3.20(81)2.56(65)1.10(28)2.85(72)00813-0100-4004, Rev FA

Catalog 2008 - 2009

Electrical Connection2.00 (51)2.00 (51)∅3.06(78)1.00 (25.4)DisplayOptionC∅DBA TABLE 27. Vortex weld-end style flowmeter

(1/2 - 4 in. (15 - 100 mm) line sizes)

Nominal Size

0.5 in.1 in.1.5 in.2 in.3 in.4 in.

A ± .10 in. (2.5 mm)

16.0 in. (406)16.0 in. (406)16.0 in. (406)16.0 in. (406)16.0 in. (406)16.0 in. (406)

B ± .05 in. (1.3 mm)

8.0 in. (203)8.0 in. (203)8.0 in. (203)8.0 in. (203)8.0 in. (203)8.0 in. (203)

C ± .20 in. (5.1 mm)

7.63 in. (194)7.74 in. (197)8.14 in. (207)8.49 in. (216)9.05 in. (230)9.60 in. (244)

Diameter D ± .031 in.

(0.79 mm).840 in. (21.34)1.315 in. (33.40)1.900 in. (48.26)2.375 in. (60.33)3.500 in. (88.90)4.500 in. (114.30)

Flow-40

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

FIGURE 8. Dimensional Drawings for Remote Mount Transmitters.Terminal Cover2.85 (72)2.00 (51)3.12 (80)3.20 (81)2.56 (65)1.10 (28)∅3.06 (78)1.00 (25)Display Option6.77(172)5.77 (147)4.35 (110)1∅2.44 (62)/2-14 NPT (ForRemote CableConduit)NOTEDimensions are in inches (millimeters)Flow-41

Product Data Sheet

Rosemount 8800D

100813-0100-4004, Rev FA

Catalog 2008 - 2009

FIGURE 9. Dimensional Drawings for Remote Mount Wafer-Style Flowmeters

(1/2-through 8 in./15 through 200 mm Line Sizes)/2-14 NPT (For Remote Cable Conduit)ENOTEDimensions are in inches (millimeters) TABLE 28. Rosemount 8800D Wafer-Style Meter

Nominal Size in. (mm)

½ (15)1 (25)1½ (40)2 (50)3 (80)4 (100)6 (150)8 (200)E Wafer Style in. (mm)

6.4 (163)6.5 (165)6.9 (175)7.6 (193)8.3 (211)9.2 (234)9.5 (241)10.4 (2)Flow-42

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

FIGURE 10. Dimensional Drawings for Flanged-and Dual Sensor Flanged-Style Remote Mount Flowmeters

(1/2-through 12 in./15 through 300 mm Line Sizes)

1/2-14 NPT (For Remote Cable 1Conduit)/2-14 NPT (For Remote Cable Conduit)EEEFlanged FlowmeterNOTEDimensions are in inches (millimeters)Dual-Sensor Style Flowmeter TABLE 29. Remote Mount, Flanged-and Dual Sensor Flowmeter Dimensions

Nominal Size in. (mm)

½ (15)1 (25)1½ (40)2 (50)3 (80)4 (100)6 (150)8 (200)10 (250)12 (300)

E Flange Style in. (mm)

6.4 (162)6.5 (165)6.8 (173)7.2 (183)7.8 (198)8.3 (211)9.5 (241)10.4 (2)11.4 (290)12.3 (313)

Flow-43

Product Data Sheet

Rosemount 8800D

Ordering Information

8800DWFRD005010015020030040060080100120SH

Vortex FlowmeterWafer styleFlanged style

Reducer Style (Flanged style only)Dual-sensor style (Flanged style only)100813-0100-4004, Rev FA

Catalog 2008 - 2009

/2 in. (15 mm) (Not available for Rosemount 8800DR)1 in. (25 mm)

11/2 Inches (40 mm)2 Inches (50 mm)3 Inches (80 mm)4 Inches (100 mm)6 Inches (150 mm)8 Inches (200 mm)10 Inches (250mm)12 Inches (300mm)316L wrought stainless and CF-3M cast stainless

UNS N06022 wrought Nickel Alloy; CW2M cast Nickel AlloyNote: See Table29 on page47

Other wetted materials are available. Consult factory for details.

A1A3A6A7(1)A8(2)B1B3B6B7(1)B8(2)C1C3C6C7(1)D0D1D2D3D4D6D7(1)G0G1G2G3G4G6G7(1)ASME B16.5 (ANSI) RF Class 150ASME B16.5 (ANSI) RF Class 300ASME B16.5 (ANSI) RF Class 600ASME B16.5 (ANSI) RF Class 900ASME B16.5 (ANSI) RF Class 1500

ASME B16.5 (ANSI) RTJ Class 150 for flange-style onlyASME B16.5 (ANSI) RTJ Class 300 for flange-style onlyASME B16.5 (ANSI) RTJ Class 600 for flange-style onlyASME B16.5 (ANSI) RTJ Class 900 for flange-style onlyASME B16.5 (ANSI) RTJ Class 1500 for flange-style onlyASME B16.5 (ANSI) RF Class 150, smooth finishASME B16.5 (ANSI) RF Class 300, smooth finishASME B16.5 (ANSI) RF Class 600, smooth finishASME B16.5 (ANSI) RF Class 900, smooth finishDIN PN 10 2526-Type D

DIN PN 16 (PN 10/16 for wafer-style)2526-Type DDIN PN 25 2526-Type D

DIN PN 40 (PN 25/40 for wafer-style) 2526-Type DDIN PN 2526-Type DDIN PN 100 2526-Type DDIN PN 160 2526-Type D

DIN PN 10 2512-Type N for flange-style onlyDIN PN 16 2512-Type N for flange-style onlyDIN PN 25 2512-Type N for flange-style onlyDIN PN 40 2512-Type N for flange-style onlyDIN PN 2512-Type N for flange-style onlyDIN PN 100 2512-Type N for flange-style onlyDIN PN 160 2512-Type N for flange-style only

Flow-44

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

H0H1H2H3H4H6H7(1)J1J2J4W1(3)W4(3)W8(3)W9(3)NE12345DPF(4)1

DIN PN 10 2526-Type E

DIN PN 16 (PN 10/16 for wafer-style) 2526-Type EDIN PN 25 2526-Type E

DIN PN 40 (PN 25/40 for wafer-style) 2526-Type EDIN PN 2526-Type EDIN PN 100 2526-Type EDIN PN 160 2526-Type EJIS 10KJIS 20KJIS 40K

Weld End, Schedule 10SWeld End, Schedule 40SWeld End, Schedule 80SWeld End, Schedule 160S

Standard: -40 to 450°F (-40 to 232°C)Extended: -330 to 800°F (-200 to 427°C)1/2 -14 NPT

M20 ϫ 1.5PG 13.5

G1/2 (One Conduit Entry)G1/2 (Two Conduit Entries)4-20 mA digital electronics (HART® protocol)

4-20 mA digital electronics (HART® protocol) with scaled pulseFOUNDATION fieldbus digital signalFlow calibration

Flow-45

Product Data Sheet

Rosemount 8800D

MTA(5)E5I5IEK5E6I6IFK6KBE1I1N1NDIAK1E7I7IGN7K7E3I3N3IHK3E4(7)A01GE(8)GM(8)M5P2C4(9)CN(9)R10R20R30RXX(10)T1V5 (11)Q4Q8Q14(12)Q25Q69(13)Q70Q71

00813-0100-4004, Rev FA

Catalog 2008 - 2009

Multivariable Options

Multivariable output with Integral Temperature SensorHazardous Locations CertificationsFM Explosion-proof, Dust Ignition-proofFM Intrinsically Safe, Division 2FM FISCO Intrinsically Safe(6)FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2CSA Explosion-proof, Dust Ignition-proof, Division 2CSA Intrinsically Safe

CSA FISCO Intrinsically Safe(6)CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2

FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2ATEX FlameproofATEX Intrinsic Safety ATEX Type nATEX Dust

ATEX FISCO Intrinsic Safety(6)ATEX Flameproof, Intrinsic Safety, Type n, DustIECEx FlameproofIECEx Intrinsic Safety

IECEx FISCO Intrinsic Safety(6)IECEx Type n

IECEx Flameproof, Intrinsic Safety, Type nChina FlameproofChina Intrinsic SafetyChina Type n

China FISCO/FNICO Intrinsic Safety(6)China Flameproof, Intrinsic Safety, Type nTIIS Flameproof

Plantweb Functionality

Basic Control: One Proportional/Integral/Derivative (PID) Function BlockConduit Electrical Connector

M12, 4-pin, Male Connector (eurofast®)

A size Mini, 4-pin, Male Connector (minifast®)Other OptionsLCD indicator

Cleaning for special services

NAMUR alarm and saturation values, high alarmNAMUR alarm and saturation values, low alarmRemote electronics with 10 ft (3,0 m) cableRemote electronics with 20 ft (6,1 m) cableRemote electronics with 30 ft (9,1 m) cable

Remote electronics with customer-specified cable length (up to 75 ft (23 m) maximum) Transient protection terminal blockExternal ground screw assemblyCertification Options

Calibration data sheet per ISO 10474 3.1B and EN 10204 3.1

Material traceability certification per ISO 10474 3.1B and EN 10204 3.1German TRB 801 Nr.45 certification per ISO 10474 3.1B and EN 10204 3.1NACE MR0103 Certificate of Compliance

Inspection certificate weld examination (wafer) per ISO 10474 3.1B and EN 10204 3.1Inspection certificate weld examination (flanged) per ISO 10474 3.1B and EN 10204 3.1

Inspection certification weld examination (flanged) per ISO 10474 3.1B (includes x-rays) and EN 10204 3.1

Flow-46

Product Data Sheet

00813-0100-4004, Rev FACatalog 2008 - 2009

Rosemount 8800D

YAYBYCYDYFYGYHYIYMYNYOYPYRYSYW

Danish QIGHungarian QIGCzech QIGDutch QIGFrench QIGGerman QIGFinnish QIGItalian QIGMandarin QIGNorwegian QIGPolish QIG

Portuguese QIGRussian QIGSpanish QIGSwedish QIG

020

1(1)Available on flanged and dual style meters from 1/2” - 8” (15-200 mm) and Reducer style meters from 1” - 6” (25-150 mm).(2)Only available for stainless steel flange and dual style meters from 1” - 8” (25-200 mm).

(3)W1, W4, W8, and W9 are only available with Meter Style F from 1/2 in. (15 mm) to 4 in. (100 mm) in SST.

(4)Includes two analog input (AI) function blocks, 1 Integrator (INT) function block, and Backup Link Active Scheduler.

(5)Available in Stainless Steel only. Available with Rosemount 8800DF from 2-in (50 mm) through 12 in. (300 mm). Available with 8800DR from 3-in (80 mm)

through 12-in (300 mm). Not available with 8800DW or 8800DD. Not available with flange codes A7, A8, B7, B8, C7, C8, D7, D8, G7, G8, H7, H8. Not available with FOUNDATION fieldbus.(6)Fieldbus Intrinsic Safe Concept available with output code F (FOUNDATION fieldbus digital signal).(7)TIIS Flameproof Approval requires G1/2 conduit entry.

(8)Not available with certain hazardous location certifications. Contact a Rosemount representative for details.

(9)NAMUR compliant operation and the alarm latch options are pre-set at the factory and can be changed to standard operation in the field.(10)XX is a customer specified length in feet.

(11)V5 only available with no approval, it is standard with the other approvals.

(12)Q14 is not available with flange codes A7, A8, B7, B8, C7, D7, G7, H7, 10in.-12in. meters, and 8800DR Reducer Vortex.

(13)Q69 available for all Nickel Alloy wafers and stainless steel wafers in line sizes 1/2 in. (15 mm), 6 in. (150 mm), and 8 in. (200 mm).

TABLE 29. Method of Construction for the 8800DF in Nickel Alloy.

NANANAWWWWWWW

WWWWWWWWWW

WWWWWWCFCFNANA

½ (15)CCCWWW1 (25)CCCWWW1½ (40)CCCWWW2 (50)CCCWCC3 (80)CCCWCC4 (100)CCCWCC6 (150)WWWCFWW8 (200)WWWCFWW10 (250)WWWNAWW12 (300)WWWNAWW

C = Nickel Alloy collar and 316 SST lap flange. If weld neck flange is required, V0022 can be ordered.W = Nickel Alloy weld neck flange.CF = Consult FactoryNA = Not Available

All 8800DR Reducer Vortex Meters with Nickel Alloy materials of construction use weld neck flanges.Flange codes other than those listed in Table 29 all use weld neck flanges.

Flow-47

Product Data Sheet

Rosemount 8800D

00813-0100-4004, Rev FA

Catalog 2008 - 2009

Standard Terms and Conditions of Sale can be found at www.rosemount.com\erms_of_saleThe Emerson logo is a trade mark and service mark of Emerson Electric Co.

Rosemount and the Rosemount logotype are registered trademarks of Rosemount Inc.PlantWeb is a mark of one of the Emerson Process Management companies.All other marks are the property of their respective owners.

Approved by the Committee of Russian Federation for Standardization, Metrology and Certification (the Gosstandart of Russia) and registered in the Russian State Register of measuring instruments.Reducer Vortex is a trademark of Rosemount Inc.MultiVariable (MV) is a trademark of Rosemount Inc.

Annubar is a registered trademark of Dieterich Standard Inc.

Mass ProBar and ProBar are trademarks of Dieterich Standard Inc.

HART is a registered trademark of the HART Communication Foundation.FOUNDATION is a trademark of the Fieldbus Foundation.Cover Photo: 8800-8800k921Emerson Process ManagementRosemount Inc.

8200 Market Boulevard

Chanhassen, MN 55317 USAT 1-800-999-9307

T (International) (952) 906-8888F (952) 949-7001www.rosemount.com

Emerson Process Management FlowNeonstraat 1 6718 WX EdeThe Netherlands T +31 (0)318 495555F +31(0) 318 495556

Emerson Process Management Asia Pacific Private Limited1 Pandan CrescentSingapore 128461T (65) 777 8211F (65) 777 0947

Enquiries@AP.EmersonProcess.com

¢00813-0100-4004Y¤

因篇幅问题不能全部显示，请点此查看更多更全内容

查看全文